Installing A Bath tub
Installing A Bath tub
Blog Article
This great article following next about Installing A Bathtub is absolutely informative. Don't skip it.
Installing a bathtub isn't exactly rocket science, yet it does require strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old tub with a new one is likewise a moderately difficult project. If the old bathtub is conveniently obtainable, the job can move quickly; if you have to open up a wall surface to get rid of the old bathtub as well as position the new bathtub, the job is a lot harder. In either situation, the project is within a home handyman's abilities, although you will certainly require a helper to move out the old tub and also embeded in the new one. Ensure you have actually certified on your own for the task and fit trying it. Instead of employing a contractor to take control of a halfway-completed project, it is better to take into consideration using one before you start. Opportunities are you may need a specialist plumber to make tube links.
This short article will aid you set up a new bath tub in your restroom if you have actually currently purchased a brand-new bathtub and do not require to change the setup of your previous water system pipes.
Your devices and product list should make up the following:
Preparing for the Installment
First of all, the supporting structure supplied with the bathroom must be fitted (if required) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to now prepare to be fitted in its final placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water system. After doing so, turn on the taps to drain pipes any water remaining in the system. The process of getting rid of the existing faucets can be quite troublesome as a result of the restricted access that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will certainly come from the pipelines. Once the supply pipes have actually been gotten rid of, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
Before carrying on to fit the brand-new faucets, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Setting up the Bathtub
Utilizing the two wooden boards under its feet, put the bath tub in the needed setting. The wood boards are practical in uniformly spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 little points.
The next goal is to ensure that the bath tub is leveled all round. This can be attained by inspecting the level and adjusting the feet on the bath tub till the level reads degree.
To mount faucets, fit the bottom of the furthest flexible faucet adapter to the proper supply pipe by making a compression join; after that do the exact same for the other tap.
Activate the water system as well as check all joints and brand-new pipework for leakages and tighten them if essential. Load the tub and also check the overflow electrical outlet and also the typical electrical outlet for leaks.
Finally, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the tub ought to wait until the bath tub has actually been utilized at least once as this will certainly resolve it right into its final position.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the placing opening in the bath/basin ensuring that the washing machines are in location in between the tap and also the sink. Protect the faucet in place with the manufacturer supplied backnut. Once the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The former kind ought to be attached to the tap finishes first, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split a rigid seal, creating the water to penetrate the wall surface between the bath and also the tiling, resulting in difficulties with dampness as well as possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes and also cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to permit the movement experienced when the tub remains in usage. The sealant can split rather early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly readily available on the marketplace. It is advisable to fit the tiles using water-resistant or waterproof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you liked our excerpt about How to Install a Bathtub. Many thanks for spending some time to read through our piece of content. Loved our piece? Please share it. Help somebody else discover it. Bless you for your time. Please stop by our site back soon.
Book Now
Report this page